Model & package intelligence
Model text, package form, tray or reel details, and visual evidence are reviewed together before RFQ feedback.
ALPS RDC1022A05
Configuration
1 options
Configuration
25+
Available for RFQ
Technical data
Product details
17
specifications
Core information
- Product name
- ALPS RDC1022A05
- Type
- ALPS
- Minimum package
- 2100 箱
Technical parameters
- Electronic Component
- Electronic Component
- Electronic Component
- ALPS
- Electronic Component
- RDC1022A05
- Electronic Component
- 1
- Package
- Through-hole
- Electronic Component
- Resistor / positions
- Electronic Component
- ±30%
- Electronic Component
- 0.49g
- Electronic Component
- 10kΩ
- Electronic Component
- 1
- Electronic Component
- BM0258859470
- Voltage
- 5V
- Electronic Component
- Electronic Component
- Electronic Component
- 2100
For datasheets, package documents, compatible-part guidance, or other technical resources, contact WMSIC customer service. Availability is confirmed case by case.
RDC1022A05 产品概述
一、产品简介
RDC1022A05 为 ALPS（阿尔卑斯）品牌的插件式可调电阻/电位器，标称阻值 10kΩ，阻值公差 ±30%，额定电压 5V。该器件以简单耐用、便于电路板插件安装和用户调节为特点，常用于低压信号电路中的电位分配、粗调与用户操作旋钮替代场合。
二、主要参数
- 阻值：10 kΩ（标称）
- 精度：±30%（公差较宽，适合非精密场合）
- 额定电压：5 V（在此电压下使用电压应不超过标称值）
- 封装：插件（适配常见 PCB 针脚孔）
- 品牌：ALPS（阿尔卑斯）
备注：产品未给出额定功耗与滑动寿命等细节，设计和选型时建议参照厂家 Datasheet 确认。
三、性能与典型应用
由于公差较大（±30%），该型号适合对精度要求不高的应用，如：
- 用户面板电位调节（音量、亮度、对比度等）
- 原型设计与教学电路，便于更换与试验
- 简单的电压分压、偏置调整
额定电压 5V 时，两端加满压的最大瞬时功率约为 P = V²/R = 25/10000 = 0.0025 W（≈2.5 mW），远小于一般固体电阻额定功率，实际允许的功率应参照厂方额定功耗。
四、设计与选型建议
- 若对阻值精度或温漂有严格要求，应选用公差更小（如 ±10%、±5%）或使用多圈精密电位器/可调电阻。
- 注意额定电压与实际工作电压，避免长期超出额定值；同时核对制造商的额定功率与滑动功耗。
- 插件封装便于手工焊接，但在振动环境下应确认机械固定与锁紧方式以防松动。
五、焊接、安装与维护
- 焊接时避免过热引脚邻近塑料件，推荐用适度温度与较短焊接时间。
- 使用前后可用适量接触清洁剂清除氧化，避免使用强腐蚀性溶剂。
- 机械寿命（滑动圈次数）和电气寿命需以厂方数据为准，频繁调整环境下宜选高寿命型号。
六、替代与扩展建议
- 需要更高精度或更高功率时，可考虑多圈精密电位器或功率型可调电阻。
- 若要求防尘、防水或更稳定性能，可选密封型或金属膜滑动类产品。
- 采购时以完整型号（含后缀）对照 ALPS 官方资料，确保引脚排列、尺寸与面板孔位匹配。
总结：RDC1022A05 为一款适用于低压、非精密场合的插件式 10kΩ 可调电阻，结构简单、便于装配，适合面板控制与原型开发。选型与长期可靠性评估应结合厂方 Datasheet 与具体应用工况。
Request for quote
Send RFQ
Use the form for single models, category sourcing, and multi-line BOM requirements.
Product sourcing intelligence
Model, package, availability, and BOM fit reviewed before quotation.
WMSIC turns product data, package visuals, BOM context, and sourcing signals into practical RFQ notes for buyers.
BOM matching & alternatives
BOM lines are compared by package, parameters, quantity, and workable alternatives for cleaner sourcing decisions.
Sourcing availability signal
Stock routes, quotation confidence, lead-time notes, and shipment feasibility are checked before sales follow-up.
Buyer sourcing scenarios
Examples of how common component sourcing requests are organized.
Typical RFQ scenarios based on the WMSIC form fields, catalog data, manual review steps, and shipment preparation workflow.
The buyer shares the full part number, package requirement, quantity, destination, and available product photos so the quotation can record the exact version under review.
A multi-line BOM is organized into direct sourcing lines, lines that need package clarification, and lines where alternative-part review is permitted.
The original manufacturer part number, datasheet revision, application, critical limits, and acceptable changes are collected before possible candidates are discussed.
Sample quantity, minimum packing, package format, target date, and courier destination are kept together in one RFQ conversation.
Package photos, model markings, board context, and the quantity needed for repair help focus the sourcing review on the relevant version.
When a suffix or package note is incomplete, the response records the open difference and requests buyer confirmation before procurement proceeds.
Packing format, carton notes, invoice details, courier option, destination, and tracking handoff are coordinated around the confirmed order.
The request connects the previously used model, current demand, package evidence, target timing, and replenishment sourcing route.
Related products
Packaged components ready for RFQ.
