WMSIC Electronic Components

HF HF3FF/012-1HTF HF3FF

ModelHF3FF/012-1HTF
PackageThrough-hole, 19x15.2mm
BrandHF
Price Price on request Electronic component prices change quickly with market supply and demand. Please refer to the latest WMSIC quotation for current pricing.
Configuration
1 options
Configuration 25+

Available for RFQ

Technical data

Product details

19 specifications

Core information

Product name
HF HF3FF / 012-1HTF
Type
HF
Minimum package
100 未知

Technical parameters

Electronic Component
Electronic Component
Electronic Component
HF
Electronic Component
HF3FF/012-1HTF
Electronic Component
1
Package
Through-hole, 19x15.2mm
Electronic Component
Power Relay
Electronic Component
7.57g
Electronic Component
4
Electronic Component
1
Electronic Component
10ms
Electronic Component
BM0257710297
Operating Temperature
40℃~+85℃
Contact Resistor
100mΩ
Coil Voltage
12V
Coil Resistor
400Ω
Coil Type
Coil

For datasheets, package documents, compatible-part guidance, or other technical resources, contact WMSIC customer service. Availability is confirmed case by case.

HF3FF/012-1HTF 产品概述

一、产品简介

HF3FF/012-1HTF 是宏发(HF)推出的一款超小型大功率继电器,单刀单掷(SPST)常开触点结构,适合在空间受限但需切换较大电流的场合使用。继电器以12V直流线圈驱动,设计紧凑、寿命可靠,适用于各类电源控制与工业控制场景。

二、主要电气参数

  • 线圈电压:12 V DC(无极性单线圈),线圈电阻 400 Ω,线圈电流约 30 mA,线圈功率 360 mW。
  • 触点形式:一组常开(单刀单掷,NO)。
  • 触点容量(电阻负载):10 A @ 28 VDC;10 A @ 277 VAC;最大切换电流 15 A。最大切换电压:277 VAC / 28 VDC。
  • 触点材料:AgSnO2,接触电阻 ≤ 100 mΩ。
  • 动作/释放时间:动作约 10 ms,释放约 5 ms。
  • 引脚数:4。
  • 工作温度范围:-40 ℃ ~ +85 ℃。

三、性能与特点

  • 小体积高承载:在超小型封装下实现10 A 的电阻负载切换能力,适合网关、继电保护或小型电源模块。
  • AgSnO2 触点:抗电弧能力强、抗焊接性能好,适应高冲击电流场合(仍建议注意涌流限制)。
  • 低线圈功耗:360 mW 的线圈功耗对应约 30 mA 驱动电流,便于与微控制器或低功耗驱动电路配合。
  • 响应快:典型动作/释放时间分别为 10 ms / 5 ms,满足一般控制逻辑要求。
  • 宽温适应:-40~+85 ℃,可在多种环境下稳定工作。

四、典型应用

  • 家用与商用电源切换、照明控制、空调及HVAC控制模块。
  • 工业控制回路、信号切换、继电保护与小功率电机的控制回路(注意涌流和感性负载保护)。
  • 仪器仪表的电源隔离与开关控制。

五、设计选型与注意事项

  • 驱动电路:线圈为无极性但若并联二极管(Flyback)使用时会引入极性,建议在驱动器(晶体管或MOSFET)侧加反向吸收器件(抑制二极管、RC 或 TVS)以抑制反向峰值和提高寿命;若要求快速释放,可采用 RC 或 TVS 代替二极管。
  • 负载类型:对电阻性负载标称 10A,感性或存在高冲击电流(如电机、电感负载)时应考虑更大的安全裕量或并联浪涌限制器,避免触点焊接或过早失效。
  • 温度与寿命:在高温或连续频繁切换工况下应适当降额使用,具体寿命与机械/电气寿命请参考完整数据手册及实测结果。
  • 封装与安装:本产品为小型继电器,引脚数 4(线圈两脚、触点两脚),具体封装形态与PCB布局请参照厂方数据表确认(用户应确认引脚排列、孔径与高度限制)。

六、采购与资料

品牌:HF(宏发),型号:HF3FF/012-1HTF。建议在设计前索取并阅读厂家完整数据手册,验证机械尺寸、引脚排布、寿命曲线和各类负载下的推荐使用条件,以确保长期可靠运行。

Request for quote

Send RFQ

Use the form for single models, category sourcing, and multi-line BOM requirements.

Send your target model and quantity.

Product sourcing intelligence

Model, package, availability, and BOM fit reviewed before quotation.

WMSIC turns product data, package visuals, BOM context, and sourcing signals into practical RFQ notes for buyers.

Electronic component model and package intelligence review on an ESD-safe inspection bench

Model & package intelligence

Model text, package form, tray or reel details, and visual evidence are reviewed together before RFQ feedback.

BOM matching and alternative component comparison workstation with protected IC samples

BOM matching & alternatives

BOM lines are compared by package, parameters, quantity, and workable alternatives for cleaner sourcing decisions.

Electronic component sourcing availability dashboard with ESD-protected samples

Sourcing availability signal

Stock routes, quotation confidence, lead-time notes, and shipment feasibility are checked before sales follow-up.

Buyer sourcing scenarios

Examples of how common component sourcing requests are organized.

Typical RFQ scenarios based on the WMSIC form fields, catalog data, manual review steps, and shipment preparation workflow.

The buyer shares the full part number, package requirement, quantity, destination, and available product photos so the quotation can record the exact version under review.

Package confirmation Typical RFQ workflow

A multi-line BOM is organized into direct sourcing lines, lines that need package clarification, and lines where alternative-part review is permitted.

Mixed BOM triage Typical RFQ workflow

The original manufacturer part number, datasheet revision, application, critical limits, and acceptable changes are collected before possible candidates are discussed.

Obsolete-part review Typical RFQ workflow

Sample quantity, minimum packing, package format, target date, and courier destination are kept together in one RFQ conversation.

Small-batch request Typical RFQ workflow

Package photos, model markings, board context, and the quantity needed for repair help focus the sourcing review on the relevant version.

Repair batch evidence Typical RFQ workflow

When a suffix or package note is incomplete, the response records the open difference and requests buyer confirmation before procurement proceeds.

Model suffix clarification Typical RFQ workflow

Packing format, carton notes, invoice details, courier option, destination, and tracking handoff are coordinated around the confirmed order.

Export handoff Typical RFQ workflow

The request connects the previously used model, current demand, package evidence, target timing, and replenishment sourcing route.

Replenishment inquiry Typical RFQ workflow

Related products

Packaged components ready for RFQ.