Model & package intelligence
Model text, package form, tray or reel details, and visual evidence are reviewed together before RFQ feedback.
Kingbright WP7113GD
Configuration
1 options
Configuration
26+
Available for RFQ
Technical data
Product details
20
specifications
Core information
- Product name
- Kingbright WP7113GD
- Type
- KINGBRIGHT
- Unit
- Electronic Component
- Minimum package
- 1000 袋
Technical parameters
- Power
- 62.5mW
- Electronic Component
- Electronic Component
- Electronic Component
- Electronic Component
- Electronic Component
- KINGBRIGHT
- Electronic Component
- WP7113GD
- Electronic Component
- 1
- Package
- Through-hole, D=5mm
- Electronic Component
- 568nm
- Electronic Component
- LEDDiode / LED
- Electronic Component
- 0.31g
- Electronic Component
- 1
- LED
- 30mcd
- LED
- 30°
- LED
- Electronic Component
- Electronic Component
- BM0230664299
- Electronic Component
- 565nm
For datasheets, package documents, compatible-part guidance, or other technical resources, contact WMSIC customer service. Availability is confirmed case by case.
WP7113GD 产品概述
一、产品简介
WP7113GD 是 Kingbright 牌翠绿色发光二极管，采用 T-1 3/4（直径 5mm）插件封装，绿色漫射透镜设计。器件在典型工作条件下提供稳定的指示光源，外观柔和、均匀，适用于面板指示、信号提示与装饰照明等场合。
二、主要参数
- 发光颜色：翠绿色（透镜为绿色漫射）
- 峰值波长：565 nm；波长中心：568 nm
- 正向电压（Vf）：2.2 V（典型，If=20 mA）
- 正向电流（If）：20 mA（最大额定工作电流）
- 功率：62.5 mW（器件额定或典型功率规格）
- 发光强度：30 mcd（If=20 mA）
- 发光角度：30°（聚光型）
- 工作温度范围：-40 ℃ 至 +85 ℃
- 封装形式：插件，D = 5 mm（T-1 3/4）
三、电气与光学特性说明
该 LED 在 20 mA 驱动下呈现峰值在 565 nm 附近的翠绿色光色，发光强度约 30 mcd，配合 30° 的窄光束角，适合需要聚光和定向指示的应用。典型正向压降为 2.2 V，设计电源时需考虑限流元件以防过流。若以 5 V 电源直接驱动，建议限流电阻 R = (Vs - Vf) / If = (5 - 2.2) / 0.02 ≈ 140 Ω；限流电阻的耗散功率约 0.056 W，选用 1/4 W 或更高功率额定的电阻即可。
四、封装与机械特性
WP7113GD 为标准 5 mm 插件 LED，漫射透镜有利于视角内亮度均匀分布，透镜本体为绿色以增强色彩饱和度。插件形式便于穿孔安装与手工或波峰焊接（请参照制造商的焊接规范）。在机械安装时注意保持透镜面清洁，避免划伤或化学腐蚀影响发光一致性。
五、设计与使用建议
- 必须采用限流措施（电阻或恒流驱动）以保证稳定寿命与一致亮度；不建议直接并联多颗 LED 无独立限流。
- 长期高温或大电流使用应适当降额运行以延长寿命（例如低于最大 If 的 70% ~ 80% 工作点）。
- 避免长时间反向电压或瞬态过压，应在电路中加入反向保护二极管或限压元件以防损坏。
- 焊接时遵守制造商推荐的温度-时间曲线，避免对塑料件的热损伤；手工焊接后建议冷却并修整引脚长度。
六、典型应用场景
适用于各类指示灯、状态显示、面板标识、工控设备指示、家用电器指示窗以及需要小角度高对比度提示的便携设备或仪器。
七、可靠性与存储建议
工作环境温度范围为 -40 ℃ 至 +85 ℃，贮存时避免潮湿、高温与强光直射。为保证长期一致性，建议按制造商 Datasheet 执行静电防护、湿热测试与老化筛选流程。
如需更详细的电气特性曲线、引脚尺寸或焊接规范，请参阅 Kingbright 官方 Datasheet 或联系供应商获取原厂技术文件。
Request for quote
Send RFQ
Use the form for single models, category sourcing, and multi-line BOM requirements.
Product sourcing intelligence
Model, package, availability, and BOM fit reviewed before quotation.
WMSIC turns product data, package visuals, BOM context, and sourcing signals into practical RFQ notes for buyers.
BOM matching & alternatives
BOM lines are compared by package, parameters, quantity, and workable alternatives for cleaner sourcing decisions.
Sourcing availability signal
Stock routes, quotation confidence, lead-time notes, and shipment feasibility are checked before sales follow-up.
Buyer sourcing scenarios
Examples of how common component sourcing requests are organized.
Typical RFQ scenarios based on the WMSIC form fields, catalog data, manual review steps, and shipment preparation workflow.
The buyer shares the full part number, package requirement, quantity, destination, and available product photos so the quotation can record the exact version under review.
A multi-line BOM is organized into direct sourcing lines, lines that need package clarification, and lines where alternative-part review is permitted.
The original manufacturer part number, datasheet revision, application, critical limits, and acceptable changes are collected before possible candidates are discussed.
Sample quantity, minimum packing, package format, target date, and courier destination are kept together in one RFQ conversation.
Package photos, model markings, board context, and the quantity needed for repair help focus the sourcing review on the relevant version.
When a suffix or package note is incomplete, the response records the open difference and requests buyer confirmation before procurement proceeds.
Packing format, carton notes, invoice details, courier option, destination, and tracking handoff are coordinated around the confirmed order.
The request connects the previously used model, current demand, package evidence, target timing, and replenishment sourcing route.
Related products
Packaged components ready for RFQ.
1 Piece Integrated Circuit for IRS20124S IRS21956S SOP-20 IRS2453DS SOP-14
- Model
- IRS20124S
- Package
