Model & package intelligence
Model text, package form, tray or reel details, and visual evidence are reviewed together before RFQ feedback.
PROD PCAQ9070MW-701 PCAQ9070MW
Configuration
1 options
Configuration
25+
Available for RFQ
Technical data
Product details
19
specifications
Core information
- Product name
- PROD PCAQ9070MW-701
- Type
- SMD-4P, 9X7MM
- Minimum package
- 700 圆盘
Technical parameters
- Electronic Component
- Electronic Component
- Electronic Component
- PROD
- Electronic Component
- PCAQ9070MW-701
- Electronic Component
- 1
- Package
- SMD-4P,9x7mm
- Electronic Component
- Common Mode Filter
- Electronic Component
- 1.53g
- Voltage
- 125V
- Electronic Component
- 1
- Channel Count
- 2
- Electronic Component
- BM0228551955
- Operating Temperature
- 25℃~+125℃
- Resistor
- 10MΩ
- Voltage
- 125V
- Current
- 5A
- @Frequency
- 700Ω@100MHz
For datasheets, package documents, compatible-part guidance, or other technical resources, contact WMSIC customer service. Availability is confirmed case by case.
PCAQ9070MW-701 产品概述
一、产品简介
PCAQ9070MW-701 是谱罗德（PROD）公司推出的一款双通道共模滤波器，封装为 SMD-4P（尺寸 9×7mm），专为抑制高频共模干扰而设计。额定电流 5A、额定电压 125V，适用于需兼顾大电流传输与高频干扰抑制的电源与信号线路。
二、主要电气参数
- 通道数：2
- 额定电流：5 A
- 阻抗：700 Ω @ 100 MHz（优秀的高频抑制能力）
- 额定电压 / 耐电压：125 V（AC）
- 直流电阻（DCR）：约 10 mΩ（低插入损耗）
- 绝缘电阻：≥ 10 MΩ
- 工作温度范围：-25 ℃ ~ +125 ℃
三、性能特点
- 高共模阻抗：在 100 MHz 附近提供高达 700 Ω 的共模阻抗，对开关电源、通信接口等产生的高频干扰有显著抑制效果。
- 低差模插入损耗：10 mΩ 的低 DCR 保证在大电流传输时功率损耗小、热量低，适合 5A 等级的电源线。
- 紧凑封装：9×7mm SMD-4P 体积小，便于在有限 PCB 面积上实现 EMI 处理。
- 可靠性：宽工作温度与较高绝缘电阻，适用于工业与消费类环境。
四、典型应用场景
- 开关电源与电源输入滤波（DC 电源轨、USB/电源适配器）
- 工业控制、通信终端的接口 EMI 抑制
- LED 驱动、车载电子（需确认车辆规范）与家电等需兼顾高电流与 EMI 管控的场合
五、PCB 布局与使用建议
- 将滤波器靠近噪声源或外部接口放置，以缩短噪声回路长度。
- 差模信号对通过中间引脚布线，保持走线对称，避免在滤波器附近形成环路。
- 对于高电流应用，尽量使用加粗走线和足够焊盘，保证热散与电流承载。
- 有必要时配合差模电容或 Y 电容形成完整的 EMI 抑制网络。
六、选型与可靠性注意
在实际设计中应注意额定电流的热升与环境温度影响，若工作温度或连续电流偏高，建议留有余量或进行热仿真验证。此外，若用于特殊行业（车规或医疗），需结合相应认证要求确认合规性。
PCAQ9070MW-701 以其高频阻抗、低 DCR 与紧凑封装为特征，是在中高电流场合下实现高效共模干扰抑制的可靠选择。若需进一步的电气图、封装尺寸或波形评估数据，可联系供应商获取详细规格书与测试曲线。
Request for quote
Send RFQ
Use the form for single models, category sourcing, and multi-line BOM requirements.
Product sourcing intelligence
Model, package, availability, and BOM fit reviewed before quotation.
WMSIC turns product data, package visuals, BOM context, and sourcing signals into practical RFQ notes for buyers.
BOM matching & alternatives
BOM lines are compared by package, parameters, quantity, and workable alternatives for cleaner sourcing decisions.
Sourcing availability signal
Stock routes, quotation confidence, lead-time notes, and shipment feasibility are checked before sales follow-up.
Buyer sourcing scenarios
Examples of how common component sourcing requests are organized.
Typical RFQ scenarios based on the WMSIC form fields, catalog data, manual review steps, and shipment preparation workflow.
The buyer shares the full part number, package requirement, quantity, destination, and available product photos so the quotation can record the exact version under review.
A multi-line BOM is organized into direct sourcing lines, lines that need package clarification, and lines where alternative-part review is permitted.
The original manufacturer part number, datasheet revision, application, critical limits, and acceptable changes are collected before possible candidates are discussed.
Sample quantity, minimum packing, package format, target date, and courier destination are kept together in one RFQ conversation.
Package photos, model markings, board context, and the quantity needed for repair help focus the sourcing review on the relevant version.
When a suffix or package note is incomplete, the response records the open difference and requests buyer confirmation before procurement proceeds.
Packing format, carton notes, invoice details, courier option, destination, and tracking handoff are coordinated around the confirmed order.
The request connects the previously used model, current demand, package evidence, target timing, and replenishment sourcing route.
Related products
Packaged components ready for RFQ.
