Model & package intelligence
Model text, package form, tray or reel details, and visual evidence are reviewed together before RFQ feedback.
XKB Connectivity TS-1101A-B-R
Configuration
1 options
Configuration
Date code within 2 years
Available for RFQ
Technical data
Product details
19
specifications
Core information
- Product name
- XKB Connectivity TS-1101A-B-R
- Type
- XKB CONNECTIVITY
- Minimum package
- 3000
Technical parameters
- Electronic Component
- XKB CONNECTIVITY
- Electronic Component
- TS-1101A-B-R
- Electronic Component
- 1
- Package
- SMD
- Electronic Component
- Electronic Component
- Electronic Component
- Switch
- Electronic Component
- 0.2g
- Electronic Component
- 1.8N
- Electronic Component
- Electronic Component
- Electronic Component
- 1
- Electronic Component
- BM0230026766
- Electronic Component
- Electronic Component
- Electronic Component
- 10
- Operating Temperature
- 30℃~+85℃
- Switch
- 3.6mm
- Switch
- 6mm
For datasheets, package documents, compatible-part guidance, or other technical resources, contact WMSIC customer service. Availability is confirmed case by case.
TS-1101A-B-R 产品概述
一、产品简介
TS-1101A-B-R 为 XKB Connectivity（中国星坤）出品的一款表面贴装轻触开关，外形小巧、动作清晰，适用于各类微型电子设备的人机输入。该型号为单刀单掷（SPST）结构，矩形按键，按键颜色为棕色，无指示灯，属于 SMD 封装，常用于按键频次不极高但要求体积和可靠性的场合。
二、主要性能参数
- 电路结构：单刀单掷（SPST）
- 按钮形状：矩形按钮（棕色）
- 动作力：160gf（约1.57N，用户资料亦可能标注为1.8N，建议以出货检验为准）
- 外形尺寸：长 6.0 mm × 宽 3.6 mm × 高 2.5 mm（立贴）
- 封装方式：SMD（立贴 / 翘脚设计以增强贴装强度）
- 触点电流：50 mA（最大）
- 额定电压：12 V DC（建议在额定值及更低电压电流下使用）
- 使用寿命：100,000 次（典型机械寿命）
- 工作温度：-30 ℃ ~ +85 ℃
- 带支架：否；带灯：否
三、结构特点与安装要点
TS-1101A-B-R 采用立贴（SMD）结构并带有翘脚形式的端子，有利于在回流焊过程中获得更好的机械支持。贴装时应按厂方推荐的焊盘尺寸和焊膏位置布局，保证焊点充分湿润以获得可靠的机械固定。回流焊温度曲线应遵循无铅或有铅工艺规范，避免过高峰值温度和过长保温时间；贴装后建议进行外观及焊接强度检验，防止因元件受力导致触点失效。
四、适用场景与注意事项
适用场景包括：便携式仪表、遥控设备、消费电子、通讯设备、家电控制面板、医疗电子（低电流接口）等。注意本开关触点电流仅 50 mA，额定电压 12 V，不能用于交流市电或大电流应用；如用于矩阵扫描或长线驱动，应考虑去抖动电路及限流/防抖策略，以延长触点寿命并改善用户体验。
五、可靠性建议与维护
在要求高可靠性的应用中，建议：
- 对关键按键进行寿命验证（样件测试）；
- 在潮湿或腐蚀性环境中采取密封或防护措施；
- 避免频繁超负荷电流与浪涌；
- 长期库存时避免高温高湿，并在装配前进行目视检验。
工作寿命为 100,000 次，实际寿命会受电气负载、环境与按键操作方式影响，设计时应留有余量。
六、选型与采购提示
订购时请确认动作力（160gf 与部分资料标注的 1.8N 存在差异时以样品为准）、外观颜色、封装形式与贴装方向。向供应商索取完整规格书与回流曲线，确认包装形式（卷带/盘装等）及出货检验报告。若产品用于关键或受规管场景，建议进行来样可靠性测试（电寿命、温度循环、振动等）。
总结：TS-1101A-B-R 是一款体积小、贴装便利、适合低电流控制的轻触开关，注重机械可靠性与成本优化。针对具体应用场景合理选型与验证，可取得稳健的使用效果。
Request for quote
Send RFQ
Use the form for single models, category sourcing, and multi-line BOM requirements.
Product sourcing intelligence
Model, package, availability, and BOM fit reviewed before quotation.
WMSIC turns product data, package visuals, BOM context, and sourcing signals into practical RFQ notes for buyers.
BOM matching & alternatives
BOM lines are compared by package, parameters, quantity, and workable alternatives for cleaner sourcing decisions.
Sourcing availability signal
Stock routes, quotation confidence, lead-time notes, and shipment feasibility are checked before sales follow-up.
Buyer sourcing scenarios
Examples of how common component sourcing requests are organized.
Typical RFQ scenarios based on the WMSIC form fields, catalog data, manual review steps, and shipment preparation workflow.
The buyer shares the full part number, package requirement, quantity, destination, and available product photos so the quotation can record the exact version under review.
A multi-line BOM is organized into direct sourcing lines, lines that need package clarification, and lines where alternative-part review is permitted.
The original manufacturer part number, datasheet revision, application, critical limits, and acceptable changes are collected before possible candidates are discussed.
Sample quantity, minimum packing, package format, target date, and courier destination are kept together in one RFQ conversation.
Package photos, model markings, board context, and the quantity needed for repair help focus the sourcing review on the relevant version.
When a suffix or package note is incomplete, the response records the open difference and requests buyer confirmation before procurement proceeds.
Packing format, carton notes, invoice details, courier option, destination, and tracking handoff are coordinated around the confirmed order.
The request connects the previously used model, current demand, package evidence, target timing, and replenishment sourcing route.
Related products
Packaged components ready for RFQ.
