Model & package intelligence
Model text, package form, tray or reel details, and visual evidence are reviewed together before RFQ feedback.
PANJIT P6SMB43CA_R2_006A1
Configuration
1 options
Configuration
24+
Available for RFQ
Technical data
Product details
19
specifications
Core information
- Product name
- PANJIT P6SMB43CA_R2_006A1
- Type
- PANJIT
- Minimum package
- 3000 圆盘
Technical parameters
- Electronic Component
- Electronic Component
- Electronic Component
- PANJIT
- Electronic Component
- P6SMB43CA_R2_006A1
- Electronic Component
- 1
- Package
- SMB
- Electronic Component
- Electronic Component
- Type
- TVS
- Electronic Component
- ESD and Surge Protection (TVS / ESD)
- Electronic Component
- 0.209g
- Electronic Component
- 1
- Electronic Component
- BM0264544586
- Operating Temperature
- 55℃~+150℃
- Voltage
- 59.3V
- Electronic Component
- IEC 61000-4-2
- Current(Ir)
- 1uA
- Voltage(VBR)
- 45.2V
For datasheets, package documents, compatible-part guidance, or other technical resources, contact WMSIC customer service. Availability is confirmed case by case.
P6SMB43CA_R2_006A1 产品概述
一、产品简介
P6SMB43CA_R2_006A1 是强茂（PANJIT）出品的一款双向瞬态电压抑制器（TVS），采用SMB封装，专为抑制电源和信号线上的浪涌、电压尖峰与静电放电（ESD）而设计。器件在10/1000µs波形下具有高能量吸收能力，适用于工业、通信与电源保护等场景。
二、主要电气参数
- 极性：双向（适用于正负反向突波保护）
- 反向截止电压 Vrwm：36.8 V（建议最大工作电压）
- 击穿电压 VBR：45.2 V（在指定电流下测得）
- 钳位电压 Vc (典型)：59.3 V（在 Ipp 条件下测得）
- 峰值脉冲电流 Ipp：10.1 A @ 10/1000µs
- 峰值脉冲功率 Ppp：600 W @ 10/1000µs（与钳位电压、脉冲电流对应）
- 反向电流 Ir：1 µA（在 Vrwm 条件下的小漏电流）
- 工作温度范围：-55 ℃ ～ +150 ℃
- 防护等级：符合 IEC 61000-4-2 静电放电抗扰度要求
三、封装与机械特性
SMB 封装具有体积小、焊接方便、散热性能良好的特点，适合标准表面贴装工艺（SMT）。器件布局时建议将 TVS 靠近受保护端口或连接器放置，以减小走线电感，提高抑制效果。
四、典型应用场景
- 工业电源与控制系统的瞬态保护（适用于最高直流工作电压接近36.8V的场合）
- 通信接口与数据线防护（如RS-485、现场总线等双向脉冲情况）
- 电池供电或分布式电源系统的浪涌保护
- 设备输入端的ESD与雷击浪涌防护，满足 IEC 61000-4-2 要求
五、选型与使用建议
- 工作电压选择：确保系统最大连续工作电压不超过 Vrwm（36.8V），否则会增加漏电或误触发风险。
- 钳位考虑：钳位电压59.3V为在标准脉冲条件下的典型值，确保被保护电路能承受该电压峰值。
- 布局建议：器件尽可能靠近受保护端口放置，走线短且粗，避免长回流路径；必要时配合串联阻抗或熔断器限制能量。
- 热管理与可靠性：尽管 Ppp 达600W，但该值对应短脉冲（10/1000µs），连续或重复冲击需按能量累积和器件热阻评估，必要时增加散热或冗余保护。
- 出货与可靠性验证：在批量使用前建议针对具体应用做浪涌、ESD 与温度循环测试。
六、注意事项
- 双向 TVS 在单向直流场合也可使用，但若系统需最低漏电流，应确认双向器件是否合适。
- 器件符合 IEC 61000-4-2 标准，但具体等级（等级 2/3/4）应参考出厂测试报告或与供应商确认。
- 焊接工艺请遵循 SMB 封装的回流曲线，以免影响性能与寿命。
总结：P6SMB43CA_R2_006A1 提供在中高能量脉冲（10/1000µs）条件下可靠的双向过压保护，适合要求较高浪涌和ESD防护能力的工业与通信类应用。关于更多应用细节与测试数据，建议参考强茂的产品规格书或联系供应商技术支持。
Request for quote
Send RFQ
Use the form for single models, category sourcing, and multi-line BOM requirements.
Product sourcing intelligence
Model, package, availability, and BOM fit reviewed before quotation.
WMSIC turns product data, package visuals, BOM context, and sourcing signals into practical RFQ notes for buyers.
BOM matching & alternatives
BOM lines are compared by package, parameters, quantity, and workable alternatives for cleaner sourcing decisions.
Sourcing availability signal
Stock routes, quotation confidence, lead-time notes, and shipment feasibility are checked before sales follow-up.
Buyer sourcing scenarios
Examples of how common component sourcing requests are organized.
Typical RFQ scenarios based on the WMSIC form fields, catalog data, manual review steps, and shipment preparation workflow.
The buyer shares the full part number, package requirement, quantity, destination, and available product photos so the quotation can record the exact version under review.
A multi-line BOM is organized into direct sourcing lines, lines that need package clarification, and lines where alternative-part review is permitted.
The original manufacturer part number, datasheet revision, application, critical limits, and acceptable changes are collected before possible candidates are discussed.
Sample quantity, minimum packing, package format, target date, and courier destination are kept together in one RFQ conversation.
Package photos, model markings, board context, and the quantity needed for repair help focus the sourcing review on the relevant version.
When a suffix or package note is incomplete, the response records the open difference and requests buyer confirmation before procurement proceeds.
Packing format, carton notes, invoice details, courier option, destination, and tracking handoff are coordinated around the confirmed order.
The request connects the previously used model, current demand, package evidence, target timing, and replenishment sourcing route.
Related products
Packaged components ready for RFQ.
