Model & package intelligence
Model text, package form, tray or reel details, and visual evidence are reviewed together before RFQ feedback.
RENESAS 5PB1102PGGI8
Configuration
1 options
Configuration
22+
Available for RFQ
Technical data
Product details
19
specifications
Core information
- Product name
- RENESAS 5PB1102PGGI8
- Type
- RENESAS
- Minimum package
- 2500 圆盘
Technical parameters
- Electronic Component
- Electronic Component
- Electronic Component
- RENESAS
- Electronic Component
- 5PB1102PGGI8
- Electronic Component
- 1
- Package
- TSSOP-8
- Electronic Component
- Clock Buffer / Driver / Distributor
- Electronic Component
- 0.163g
- Electronic Component
- 1
- Features
- Output /; and; / Isolated Driver
- Electronic Component
- BM0257323856
- Operating Temperature
- 40℃~+85℃
- Operating Voltage
- 1.8V~3.3V
- Channel Count
- 1
- Output Channel Count
- 2
- Output Frequency
- 200MHz
- Electronic Component
- Electronic Component
For datasheets, package documents, compatible-part guidance, or other technical resources, contact WMSIC customer service. Availability is confirmed case by case.
5PB1102PGGI8 产品概述
一、概览
5PB1102PGGI8 为瑞萨（RENESAS）系列时钟 IC，面向需要稳定、高速时钟源的电子系统。器件支持最高输出频率 200 MHz，工作温度范围为 -40℃ 至 +85℃，适合工业级与车规级相近环境下的时钟发生与分配应用。
二、关键参数
- 最大输出频率：200 MHz
- 工作电压（多电源设计）：2.375 V ～ 2.625 V；1.71 V ～ 1.89 V；3.135 V ～ 3.465 V
- 工作温度：-40℃ ～ +85℃
- 封装：TSSOP-8（8 引脚）
- 品牌：RENESAS（瑞萨）
（注：上述为器件的基础参数，详细的 AC/DC 特性、引脚功能及时序需参照官方数据手册核实。）
三、封装与引脚要点
器件以 TSSOP-8 小封装交付，便于中高密度 PCB 布局。由于为时钟类器件，封装引脚应优先考虑电源去耦、地平面完整性与输出走线阻抗控制。若器件为多电源结构，请严格按数据手册指定的电源序列和隔离方案接入。
四、典型应用场景
- FPGA/ASIC 的时钟发生与分配
- 数据采集、模数/数模转换器驱动时钟
- 通信设备、网络接口的本地振荡与同步
- 工业控制与嵌入式系统中的时序基准
五、设计与使用建议
- 电源管理：采用接近芯片引脚的多级去耦（如 0.1 μF 与 1 μF 并联），并在不同电源域间使用合适滤波与阻隔元件，避免电源干扰耦合至时钟输出。
- 布线与阻抗：输出走线尽量采用受控阻抗的微带或带状线，避免长孤线（stub），必要时添加终端电阻以减少反射。
- 接地与屏蔽：保持连续的接地平面，电源与模拟/数字地分区并在单点回流处短接以减小环路面积。
- 时序验证：使用带宽足够的示波器或相位噪声分析仪评估抖动与相位噪声，确保满足系统定时要求。
- ESD 与热保护：贴片与测试过程中注意防静电措施，封装散热虽不大，但应避免连续高温工作并留出通风或散热路径。
六、可靠性注意
在 -40℃ 至 +85℃ 的工作条件下使用时，应考虑电压容差与环境变化造成的频率漂移。长期可靠性测试（温度循环、湿热、振动）建议参考瑞萨提供的可靠性规范。
七、采购与替代
购买与选型时，请以瑞萨官方数据手册与型号说明为准，若需替代件或跨厂商替代，建议对比输出频率范围、电源架构、抖动规格与封装引脚一致性，再行验证兼容性。
如需更详细的引脚功能表、时序图、典型应用电路或参考布局文件，可提供数据手册号或联系瑞萨技术支持获取官方资料。
Request for quote
Send RFQ
Use the form for single models, category sourcing, and multi-line BOM requirements.
Product sourcing intelligence
Model, package, availability, and BOM fit reviewed before quotation.
WMSIC turns product data, package visuals, BOM context, and sourcing signals into practical RFQ notes for buyers.
BOM matching & alternatives
BOM lines are compared by package, parameters, quantity, and workable alternatives for cleaner sourcing decisions.
Sourcing availability signal
Stock routes, quotation confidence, lead-time notes, and shipment feasibility are checked before sales follow-up.
Buyer sourcing scenarios
Examples of how common component sourcing requests are organized.
Typical RFQ scenarios based on the WMSIC form fields, catalog data, manual review steps, and shipment preparation workflow.
The buyer shares the full part number, package requirement, quantity, destination, and available product photos so the quotation can record the exact version under review.
A multi-line BOM is organized into direct sourcing lines, lines that need package clarification, and lines where alternative-part review is permitted.
The original manufacturer part number, datasheet revision, application, critical limits, and acceptable changes are collected before possible candidates are discussed.
Sample quantity, minimum packing, package format, target date, and courier destination are kept together in one RFQ conversation.
Package photos, model markings, board context, and the quantity needed for repair help focus the sourcing review on the relevant version.
When a suffix or package note is incomplete, the response records the open difference and requests buyer confirmation before procurement proceeds.
Packing format, carton notes, invoice details, courier option, destination, and tracking handoff are coordinated around the confirmed order.
The request connects the previously used model, current demand, package evidence, target timing, and replenishment sourcing route.
Related products
Packaged components ready for RFQ.
