Model & package intelligence
Model text, package form, tray or reel details, and visual evidence are reviewed together before RFQ feedback.
TECH PUBLIC XC6206P182MR(1uA) XC6206P182MR
Configuration
1 options
Configuration
25+
Available for RFQ
Technical data
Product details
19
specifications
Core information
- Product name
- TECH PUBLIC XC6206P182MR(1u A)
- Type
- SOT-23-3L
- Minimum package
- 3000 圆盘
Technical parameters
- Electronic Component
- Electronic Component
- Electronic Component
- 70mV@(30mA)；240mV@(100mA)
- Electronic Component
- TECH PUBLIC
- Electronic Component
- XC6206P182MR(1uA)
- Electronic Component
- 1
- Package
- SOT-23-3L
- Electronic Component
- Linear Regulator(LDO)
- Electronic Component
- 0.039g
- Electronic Component
- 1
- Electronic Component
- BM0257708796
- Operating Temperature
- 25℃~+85℃@(Ta)
- Operating Voltage
- 7V
- Output
- Electronic Component
- Output Voltage
- 1.8V
- Output Current
- 200mA
- Output Type
- Electronic Component
For datasheets, package documents, compatible-part guidance, or other technical resources, contact WMSIC customer service. Availability is confirmed case by case.
XC6206P182MR (1µA) — 线性稳压器产品概述
一 概述
XC6206P182MR 是一款低静态电流、固定输出的正向线性稳压器，封装为 SOT-23-3，输出电压为 1.8V，最大输出电流 200mA。器件集成过流保护与短路保护，工作温度范围 -25℃～+85℃（Ta）。静态电流仅 1µA，适合对待机功耗要求严格的便携与电池供电系统。
二 主要参数（摘要）
- 输出类型：固定（1.8V）
- 最大输出电流：200mA
- 压降（典型）：70mV @ 30mA；240mV @ 100mA（随负载电流增大而上升）
- 静态电流 Iq：1µA（低静态电流）
- 保护功能：过流保护、短路保护
- 工作温度：-25℃ ～ +85℃（Ta）
- 输出极性：正极输出
- 通道数：单路
- 封装：SOT-23-3L
三 电气与使用要点
- 输入电压要求：确保输入电压高于输出电压加上压降余量。由于压降随电流上升而增加，建议在满载附近留有足够余量（实际系统设计中可预留 0.3V～0.7V 视工作电流而定）。
- 启动与瞬态：稳压器在负载突变时会有短时输出位移，配合合适的输入/输出旁路电容可改善瞬态响应。
- 保护行为：器件内置过流/短路保护，遇过载时会限制输出电流并可能引入热限与折返，需在系统中预留恢复策略。
四 封装与引脚（SOT-23-3）
- 引脚功能通常为：Vin、GND、Vout（请参照具体数据手册确认引脚排列）。
- 小封装利于空间受限设计，但需注意散热能力有限，印制板铜箔面积与过孔布局对功耗管理影响显著。
五 应用场景
- 电池供电便携终端（传感器节点、可穿戴设备）
- 低功耗 MCU 和外设供电（1.8V 核心电压）
- 通信模块、ADC 前端、低压模拟电路的稳压供电
六 设计与版图建议
- 输出电容：为保证稳定与良好瞬态响应，使用低 ESR 的陶瓷电容（例如 1µF～10µF）靠近 VOUT 与 GND 布置；输入侧也应放置 1µF 左右的旁路电容以抑制输入阻抗。
- 布线与散热：若 Vin–Vout 差值与输出电流水平导致较大功耗，需增大器件附近的铜面积并考虑多层板接地平面或散热过孔，以降低结壳温升。
- 启动与复位：在对上电顺序或复位有严格要求的系统中，应评估稳压器上电特性及复位时序，必要时加上外部复位/监控电路。
- 噪声与滤波：对噪声敏感的模拟电路，建议在输出端增加适当的滤波网络或后级低噪放大器。
七 总结
XC6206P182MR（台舟电子/TECH PUBLIC）是一款面向低功耗、空间受限设计的 1.8V 固定输出线性稳压器，适用于对静态电流有严格要求的电池供电设备。选型时需关注输入电压余量、输出电容配置及板级散热设计，以确保在最大输出电流下稳定可靠运行。欲获取详细电气特性曲线与引脚排列，请参考厂商数据手册以完成最终设计验证。
Request for quote
Send RFQ
Use the form for single models, category sourcing, and multi-line BOM requirements.
Product sourcing intelligence
Model, package, availability, and BOM fit reviewed before quotation.
WMSIC turns product data, package visuals, BOM context, and sourcing signals into practical RFQ notes for buyers.
BOM matching & alternatives
BOM lines are compared by package, parameters, quantity, and workable alternatives for cleaner sourcing decisions.
Sourcing availability signal
Stock routes, quotation confidence, lead-time notes, and shipment feasibility are checked before sales follow-up.
Buyer sourcing scenarios
Examples of how common component sourcing requests are organized.
Typical RFQ scenarios based on the WMSIC form fields, catalog data, manual review steps, and shipment preparation workflow.
The buyer shares the full part number, package requirement, quantity, destination, and available product photos so the quotation can record the exact version under review.
A multi-line BOM is organized into direct sourcing lines, lines that need package clarification, and lines where alternative-part review is permitted.
The original manufacturer part number, datasheet revision, application, critical limits, and acceptable changes are collected before possible candidates are discussed.
Sample quantity, minimum packing, package format, target date, and courier destination are kept together in one RFQ conversation.
Package photos, model markings, board context, and the quantity needed for repair help focus the sourcing review on the relevant version.
When a suffix or package note is incomplete, the response records the open difference and requests buyer confirmation before procurement proceeds.
Packing format, carton notes, invoice details, courier option, destination, and tracking handoff are coordinated around the confirmed order.
The request connects the previously used model, current demand, package evidence, target timing, and replenishment sourcing route.
Related products
Packaged components ready for RFQ.
