Model & package intelligence
Model text, package form, tray or reel details, and visual evidence are reviewed together before RFQ feedback.
Taiwan Lu Hai SL0420-100M SL0420
Configuration
1 options
Configuration
26+
Available for RFQ
Technical data
Product details
19
specifications
Core information
- Product name
- SL0420-100M
- Type
- Taiwan Luhai
- Minimum package
- 3000 圆盘
Technical parameters
- Electronic Component
- Electronic Component
- Electronic Component
- Electronic Component
- Electronic Component
- SL0420-100M
- Electronic Component
- 1
- Package
- SMD,4.5x4.1mm
- Electronic Component
- SMD Inductor
- Electronic Component
- ±20%
- Electronic Component
- 0.263g
- Inductor
- 10uH
- Electronic Component
- 1
- Electronic Component
- BM0265001090
- Current
- 2A
- Resistor(DCR)
- 200mΩ
- Electronic Component
- Electronic Component
- Electronic Component
- 3000
- and Current(Isat)
- 2.5A
For datasheets, package documents, compatible-part guidance, or other technical resources, contact WMSIC customer service. Availability is confirmed case by case.
SL0420-100M 产品概述
一、产品简介
SL0420-100M 为台湾陆海（Lu Hai）推出的一体成型贴片合金电感，封装为SMD，外形尺寸约4.5 x 4.1 mm。标准感值10 μH，公差±20%，属于面向中功率应用的功率电感器件，适用于开关电源输出滤波、直流降压转换器及电源线抗干扰等场合。
二、主要特性
- 感值：10 μH ±20%（室温标称值）
- 额定电流：2.0 A（连续工作参考）
- 饱和电流（Isat）：2.5 A（进入磁饱和、感值显著下降的参考值）
- 直流电阻（DCR）：约200 mΩ（在25°C条件下）
- 封装：SMD，尺寸4.5×4.1 mm；一体成型合金结构，机械强度好，焊接可靠
三、电气与热性能要点
- 在额定电流2 A时，DCR导致的铜损约为I^2·R = 0.8 W，器件会产生明显热量，PCB散热布局需充分考虑。
- 建议连续工作电流按照热和效率要求适当降额（建议取额定电流的70%～80%作为长期可靠的参考值），以避免过热和感值衰减。
- 饱和电流2.5 A为器件进入磁饱和的参考，应避免长期在接近或超过该值的工况下使用，以保证滤波性能稳定。
四、典型应用
- 开关稳压器（降压/升压）输出滤波电感
- 电源模块、点对点供电（POL）电路
- 电源输入滤波与共模/差模噪声抑制（与电容配合）
- 工业控制与消费电子中等电流路径的能量存储
五、封装与布局建议
- 推荐采用回流焊工艺，焊盘尺寸与锡膏厚度按照厂方推荐或行业经验优化，以保证良好热传导与机械可靠性。
- 由于DCR较高，应在器件下方或附近设计厚铜或过孔散热通道，必要时在对流方向提供空气流动，降低结温。
- 放置时避免热源近旁堆叠，确保感值温漂与寿命。
六、选型与验证建议
- 在样机阶段测量实际DCR、感值随电流的变化曲线与温升曲线，确认满足系统效率与热裕量要求。
- 若系统需要更低损耗或更高持续电流，应考虑更低DCR或更大体积的电感件。
- 与电容、开关频率配合时，验证总体滤波性能与输出纹波。
七、品质与储存注意
- 建议按照一般电子元件储存规范：避免潮湿、高温与直接阳光；未用贴片料盘保持原装封装以防氧化与机械损伤。
- 对回流焊温度曲线采用符合无铅焊接的标准曲线，避免重复高温循环。
八、结论
SL0420-100M 为一款面向中等电流需求的一体成型贴片合金电感，具有结构坚固、封装紧凑的优点。其10 μH、2 A等级适合多数POL及电源滤波场景，但需重视200 mΩ 的DCR带来的功耗与热管理要求。针对热和效率敏感的设计，应在PCB布局与选型阶段进行充分验证与适度降额使用。
Request for quote
Send RFQ
Use the form for single models, category sourcing, and multi-line BOM requirements.
Product sourcing intelligence
Model, package, availability, and BOM fit reviewed before quotation.
WMSIC turns product data, package visuals, BOM context, and sourcing signals into practical RFQ notes for buyers.
BOM matching & alternatives
BOM lines are compared by package, parameters, quantity, and workable alternatives for cleaner sourcing decisions.
Sourcing availability signal
Stock routes, quotation confidence, lead-time notes, and shipment feasibility are checked before sales follow-up.
Buyer sourcing scenarios
Examples of how common component sourcing requests are organized.
Typical RFQ scenarios based on the WMSIC form fields, catalog data, manual review steps, and shipment preparation workflow.
The buyer shares the full part number, package requirement, quantity, destination, and available product photos so the quotation can record the exact version under review.
A multi-line BOM is organized into direct sourcing lines, lines that need package clarification, and lines where alternative-part review is permitted.
The original manufacturer part number, datasheet revision, application, critical limits, and acceptable changes are collected before possible candidates are discussed.
Sample quantity, minimum packing, package format, target date, and courier destination are kept together in one RFQ conversation.
Package photos, model markings, board context, and the quantity needed for repair help focus the sourcing review on the relevant version.
When a suffix or package note is incomplete, the response records the open difference and requests buyer confirmation before procurement proceeds.
Packing format, carton notes, invoice details, courier option, destination, and tracking handoff are coordinated around the confirmed order.
The request connects the previously used model, current demand, package evidence, target timing, and replenishment sourcing route.
Related products
Packaged components ready for RFQ.
