Model & package intelligence
Model text, package form, tray or reel details, and visual evidence are reviewed together before RFQ feedback.
JSMSEMI S9013
Configuration
1 options
Configuration
Date code within 2 years
Available for RFQ
Technical data
Product details
19
specifications
Core information
- Product name
- JSMSEMI S9013
- Type
- JSMSEMI
- Minimum package
- 1000 圆盘
Technical parameters
- Electronic Component
- Electronic Component
- Electronic Component
- JSMSEMI
- Electronic Component
- S9013
- Electronic Component
- 1
- Package
- TO-92-3
- Electronic Component
- 1 NPN
- Electronic Component
- Transistor(BJT)
- Electronic Component
- 0.057g
- Electronic Component
- 1
- Electronic Component
- BM0227639671
- Operating Temperature
- 55℃~+150℃
- Transistor Type
- NPN
- Frequency(f T)
- 150MHz
- Power Dissipation(Pd)
- 300mW
- Electronic Component
- Electronic Component
- Electronic Component
- 1000
For datasheets, package documents, compatible-part guidance, or other technical resources, contact WMSIC customer service. Availability is confirmed case by case.
S9013 产品概述
一、主要特性
S9013 为 JSMSEMI（杰盛微）出品的通用 NPN 小信号晶体管，适用于低压、中等电流场合。关键参数包括：直流电流增益 hFE = 144（测试条件 50mA、VCE=1V）、集电极最大电流 Ic = 500mA、集电极-射极击穿电压 VCEo = 25V、耗散功率 Pd = 625mW、特征频率 fT = 150MHz、集电极截止电流 Icbo = 100nA、射基极击穿电压 Vebo = 5V、饱和电压 VCE(sat) ≈ 600mV（在 500mA、50mA 条件下）。工作温度范围宽 (-55℃ ~ +150℃)，封装为常见的 TO-92-3，适合通用电路板装配与手工焊接。
二、电气参数要点
- 低电压工作：VCEo=25V，推荐用于 12V 以下电路或有保护措施的 25V 系统。
- 中等电流能力：Ic 峰值可达 500mA，但长时间连续工作受限于封装散热与 Pd（625mW）。
- 开关与放大：fT=150MHz 表明在小信号放大时有良好高频响应，但在大电流开关时速度受荷载和寄生电容影响。
- 注意反向击穿：Vebo=5V，禁止将基-射极反向电压超过此值。
三、典型应用
- 低功耗开关与继电器驱动（配合限流与保护电路）
- 前置放大器、信号放大与电平转换
- MCU 输出扩流、指示灯驱动、小型电机或继电器驱动（需加保护二极管/限流）
- 通用原型与教学电路
四、设计与使用要点
- 热管理：TO-92 封装散热受限，建议计算实际功耗并留有热余量。连续功耗接近 Pd 时需降额使用或外部散热。
- 饱和驱动：为获得低 VCE(sat)，应将基极驱动设计为强迫饱和（Fb≈10）。例如需 Ic=100mA 时，若驱动电压为 5V，基极电阻可近似选为 Rb=(5-0.7)/(100/10)≈430Ω。
- 感性负载保护：驱动继电器或线圈时应并联反向二极管或吸收器以防止瞬态超压。
- 防静电与焊接：焊接温度与时间应符合封装热容要求，避免长期高温。基极反向电压不要超过 5V。
五、封装与可靠性
TO-92-3 封装方便穿孔安装与手工调试，适用于小批量与量产板上使用。器件在 -55℃~+150℃ 的工作范围内适应性强，但长期高温会加速老化，建议在高温工况下进行电气降额并加强散热设计。
六、选型建议
S9013 适合要求中等电流、低压和良好增益的小功率放大与开关场合。若系统需长时间大电流、较高功耗或更低饱和压，应考虑功率更高的封装或功率晶体管；若需更高频率特性，可选 fT 更高的专用射频晶体管。选型时以实际 Ic、Pd 与热阻为主，预留安全裕量。
Request for quote
Send RFQ
Use the form for single models, category sourcing, and multi-line BOM requirements.
Product sourcing intelligence
Model, package, availability, and BOM fit reviewed before quotation.
WMSIC turns product data, package visuals, BOM context, and sourcing signals into practical RFQ notes for buyers.
BOM matching & alternatives
BOM lines are compared by package, parameters, quantity, and workable alternatives for cleaner sourcing decisions.
Sourcing availability signal
Stock routes, quotation confidence, lead-time notes, and shipment feasibility are checked before sales follow-up.
Buyer sourcing scenarios
Examples of how common component sourcing requests are organized.
Typical RFQ scenarios based on the WMSIC form fields, catalog data, manual review steps, and shipment preparation workflow.
The buyer shares the full part number, package requirement, quantity, destination, and available product photos so the quotation can record the exact version under review.
A multi-line BOM is organized into direct sourcing lines, lines that need package clarification, and lines where alternative-part review is permitted.
The original manufacturer part number, datasheet revision, application, critical limits, and acceptable changes are collected before possible candidates are discussed.
Sample quantity, minimum packing, package format, target date, and courier destination are kept together in one RFQ conversation.
Package photos, model markings, board context, and the quantity needed for repair help focus the sourcing review on the relevant version.
When a suffix or package note is incomplete, the response records the open difference and requests buyer confirmation before procurement proceeds.
Packing format, carton notes, invoice details, courier option, destination, and tracking handoff are coordinated around the confirmed order.
The request connects the previously used model, current demand, package evidence, target timing, and replenishment sourcing route.
Related products
Packaged components ready for RFQ.
